Difference between revisions of "Brake Master Cylinder"
(→Replacing a Master Cylinder on North American Cars) |
(→Removing the low brake fluid sensor) |
||
| Line 25: | Line 25: | ||
# Unplug the low brake fluid sensor from the harness | # Unplug the low brake fluid sensor from the harness | ||
| − | # Pry off the black plastic cap. Be careful it pops right off. - I still haven't found mine. | + | # Pry off the black plastic cap. Be careful it pops right off. - I still haven't found mine. It is only available b purchasing a new reservoir. Hopefully it is a standard 1990s junkyard part. |
# Pull the guts of the sensor straight up. Only the black plastic cap holds in on so this is easy. | # Pull the guts of the sensor straight up. Only the black plastic cap holds in on so this is easy. | ||
Revision as of 00:19, 22 August 2012
Contents
Info
7/8" bore
Replacing a Master Cylinder on Federal
There are major differences between the North American (NA) (also know as Federal) and the Rest Of the World (ROW) master cylinder. The NA version has three (3) pipes, other have four (4) pipes. There is also a great amount of difference between Left and Right hand drive cars. The remainder of this portion will deal with the Federal version.
It is difficult to remove the master cylinder due to stuff in the way. I am writing this after just completing the removal.
Preparation
The first few steps are to gain access to the master cylinder and reduce the amount of fluids to spill.
- Drain the radiator – on NA cars there is a drain on the lower left. Don't forget to tighten this back up. Be careful when tightening this piece it is plastic and it is a Lotus only part.
- Remove the overflow bottle
- Remove the overflow bottle retain bracket. Don't worry the nuts for the 3 small bolts are an integral part of the frame and won't move or fall out.
- Remove the inlet pipe that goes between the intake manifold and the inter-cooler.
- Remove the vacuum hose - I had to cut mine off, don't worry it is a standard 7/16" vacuum hose.
- Remove as much of the brake fluid as you can.
Removing the low brake fluid sensor
- Unplug the low brake fluid sensor from the harness
- Pry off the black plastic cap. Be careful it pops right off. - I still haven't found mine. It is only available b purchasing a new reservoir. Hopefully it is a standard 1990s junkyard part.
- Pull the guts of the sensor straight up. Only the black plastic cap holds in on so this is easy.
Separating the Reservoir from the Master Cylinder
On Federal cars the clutch cable passes between the master cylinder and the reservoir. Now the real fun starts!
I need to figure out how to post my pictures. Insert picture of the cable passing between the 2 components.
It would probably be best to remove the reservoir at this point. I didn't do it until I had freed the master cylinder and reservoir as a unit. It took considerable strength to hold the master cylinder while applying a pry force. My Internet search suggested placing the master cylinder in a vice for this operation. If I were performing this repair again I would attempt to remove the reservoir at this point.
The reservoir is held in by the 2 rubber gaskets. Separating the reservoir from the master cylinder involves lots of wiggling, brute strength and a tool to pry the 2 pieces apart. Note that the rubber gaskets stay with the master cylinder.
Attempt to break the seal between the rubber gasket and the reservoir. Wiggle the reservoir around a bit. Gently pry between the plastic reservoir base and the rubber gaskets. Insert a tool (I used a ratchet handle) between the 2 parts forward of the forward most gasket and apply force. The forward part of the reservoir will pop out. Swing it out of the way and pry more toward the back gasket. A fair amount of force was necessary to achieve separation.
Undoing the Hydraulic Pipes
Breaking the fittings free required that I use "Flare Nut Wrenches". When I tried a standard open end wrench all I accomplished was to start rounding off the corners of the fitting.
Once you have broken all 3 fittings free it is probably best to move on to the 2 nuts that hold the master cylinder to the vacuum booster. I didn't and I buggered up one of the threads while loosening a nut holding the master cylinder.
To be continued. Time to go to bed.
Cross reference
Make Model Year Application
PONTIAC Asuna (Canada) 1990-1991 4-1.6L F/inj. (6)
PONTIAC Asuna (Canada) 1989-1990 4-2.0L F/inj. (K) w/ Power Brakes Stamped 2631
PONTIAC Lemans-FWD 1990-1993 4-1.6L F/inj. (6)
PONTIAC Lemans-FWD 1989-1990 4-2.0L F/inj. (K) w/ Power Brakes Stamped 2631
PONTIAC Optima 1990-1993 4-1.6L F/inj. (6)
PONTIAC Optima 1989-1990 4-2.0L F/inj. (K) w/ Power Brakes Stamped 2631
Possible US sources
AC-DELCO 174-812
AC-DELCO 18M478
AC-DELCO 18M555
AUTOSPECIALTY M-13002
BECK/ARNLEY 072-8751
CARQUEST E150607
CENTRIC 130.36002
EIS E150607
GENERAL MOTORS 3492362
ITM 25-01609
LUCAS GIRLING 211526
NAPA (BRAKE) 39869
RAYBESTOS MC-39869
From GLS Autoparts
Possible UK sources
Unipart Brake Master Cylinder:
Product Code: BUYOUT0014957
Description: FPSPMH392 MASTER C
Price incl VAT: 110.09 GBP (2007 price)
